16.5″ x 5.9″ New Amada Vertical Plate Saw VM420

F.O.B. Factory
Terms: Check with Order

SKU: 19013 Categories: , ,

Description

16.5″ x 5.9″ New Amada Vertical Plate Saw VM420 Specifications:

Capacity
16.5″ x 5.9″
Throat Depth
11.8″
Work Load Capacity
441 lbs
Saw Blade
 
Blade Size (L x T x W)
11’6″ x 0.042″ x 1-1/4″
Blade Speed
49.2 – 295 ft/min by Inverter
Tension Control
Hydraulic
Blade Control
 
Cutting Control
Hydraulic Pressure – Flow Control Valve
Vise Operation 
 
Type 
Front and Rear Vise
Control
Hydraulic Full Stroke Cylinder
Motors
 
Saw Blade
3 HP
Hydraulic Pump
1 HP
Wire Brush
1/16 HP
Cutting Fluid Pump
1/8 HP
Backgauge
1/4 HP
Power Requirement
 
Power Voltage 
AC220V±10%, 3 PH, 60 Hz
All Other Voltages Require Transformer
Power Requiremnet
5.5 kVA
Cutting Fluid  
Tank Capacity 12.1 gal
Pump Type Electric
Hydraulic  
Tank Capacity 10.5 gal
Pressure Setting 384 psi
Chip Disposal Manual
Feed  
Mechanism Table Feed, Hydraulic
Stroke 17.52″
NC Back Gauge 0.118″ – 12.008″
Machine Dimensions (W x L x H) 59.64″ x 32.67″ x 73.78″
Table Height 29.5″
Machine Weight 1,984 lbs

 

16.5″ x 5.9″ New Amada Vertical Plate Saw VM420 Standard Features:

  • 3 H.P.
  • 1-1/4″ Blade
  • Inverter Blade Speed Change
  • Hydraulic Clamp
  • Hydraulic Blade Tension
  • Auto Backgauge Stopper
  • T Grove Table
  • Drive Wheel Transmission
    • The drive motor’s variable speed driven pulley is directly coupled to the high efficiency planetary gear reducer and the drive wheel is mounted on the rotating output case of the gear reducer. The pulleys and belt are guarded against both fluids and dust for long life with low maintenance.
  • Band Wheels & Drive System
    • The band wheels are cast iron for long, productive life. The drive wheel is mounted on the rotating outer case of the planetary gear reducer. This direct coupling of the drive wheel to the rotating outer case of the reducer provides deflection-free torque transfer and ensures the wheel runs true regardless of tension stresses or cutting loads. The inherent high efficiency of the planetary gear reducer means more power is delivered to the blade. The idler wheel spindle assembly incorporates tapered roller bearings for greater rigidity and long service life. The wheel tracks the blade so that the back of the blade contacts the wheel flange to support the back of the band.
  • Band Deviation Monitor
    • The detector constantly displays the current blade cutting conditions and has independently adjustable limits for each direction. If the blade deviation exceeds either limit for more than 90 seconds, the machine control will stop the machine. Using the cutting display in conjunction with the runout detector, enables the operator optimize the cutting performance to achieve the desired rate and accuracy.
  • Power Positioning of Upper Saw Guide Arm
    • The movable guide is hydraulically positioned using the manual valve on the control panel. After it is in the desired position, it is locked to the way bar by a short stroke hydraulic cylinder.
  • Pressure/Flow Feed Control
    • The independent pressure and flow controls in series ensure the optimum cutting rate can be obtained regardless of section or alloy being cut. The pressure control determines the cutting force applied to the blade and the flow control sets the maximum feed rate of the head. For example, for difficult to machine materials the pressure is set higher than free machining alloys and the flow is set lower, as shown on the escutcheons above the control knobs.
  • Table Guiding
    • The rigid feed table is mounted on precision LM linear bearings. This rigidity enables the machine to cut all tough and hard machinable alloys.
  • Manual Positioning of Saw Table
    • The table positioning push buttons actuate solenoid valves to rapidly position the saw head forward or reverse. The manual movement of the head is controlled by push buttons on the control panel with safety interlocks.
  • Idler Wheel Motion Detector
    • The idler wheel motion detector will turn off the blade drive in the case where a blade breaks or is jammed in the workpiece. This feature prevents premature wear on the drive wheel from a stalled band.
  • Ammeter
    • The ammeter displays the current draw on the blade drive motor.

 

About Us

Worldwide Machine Tool is the leader in providing full sales, parts and service, financing, transportation and training of new and used machine tools for chip and fabrication clients across the United States, Canada and Mexico. Our warehouse and office is located just minutes north of Columbus, Ohio. With over 25 years of experience in the industrial machine tool industry, we have the knowledge and expertise to provide our customers with the best customer service support and technical expertise on all new and used machine tools to meet their needs.

We buy and sell new and used ironworkers, shears, lathes, milling machines, drills, saws, press brakes, routers, turret punch models, presses, welders, deburring and beveling machines, plate rolls, laser, waterjets and associated tooling and accessories. We take pride in being a trustworthy partner that our customers rely on through the years. Our experienced sales team would love to help you with your next machine tool purchase. Give us a call today or fill out the Request A Quote form on the right side of this page.

Call 614-255-9000 or Contact us today to experience the Worldwide Machine Tool difference.

F.O.B Factory

Check us out on Twitter, Facebook, Youtube, LinkedIn and Instagram

Worldwide Machine Tool LLC.

Terms and Conditions: https://www.worldwidemachinetool.com/terms-conditions/

All product information including but not limited to price, specifications, color, photos, equipped with and features are subject to change.

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.