18″ x 22″ New Marvel Vertical Tilt Frame Bandsaw Series 8-Mark-II

18″ x 22″ New Marvel Vertical Tilt Frame Bandsaw Series 8-Mark-II for sale at Worldwide Machine Tool

SKU: 30951 Categories: , ,

Description

18″ x 22″ New Marvel Vertical Tilt Frame Bandsaw Series 8-Mark-II Specifications:

Capacity: 90° 18″ x 22″
Capacity: 45°
18″ x 12.75″
Speed Range
50 – 450 fpm infinitely variable with inverter drive.
Front Mounted Speed Control
Allows blade speed to be adjusted from operator’s control station.
Feed Range
0 – 140 lbs. infinitely variable with control on operator’s panel and Automatic Column Return.
T-Slotted Work Table
Work area 24.25″ x 33″; table height 34.5″; four machined T-slots accept .625″ (15.5 mm) T-Bolts.
Miter Cutting
Column and blade tilt up to 45° right and left of vertical; work always stationary. Built in protractor.
Quick-Action Vise
Maximum opening 18″. Jaws can be shifted to either right or left side of blade. Jaws are 6″ high, 12″ wide.
Automatic Stops
Adjustable stops can be pre-set to stop advance and return of blade and to stop motor at any location within the 18″ travel of the blade.
Coolant System
Built in with Flood system, available with added optional drop lubrication system. Controlled by on-off selector switch at operator’s station. Tank capacity 21 gallons.
Flusing Hose
Washes chips from hard to get at places reducing clean-up time.
Power Chip Brush
Together with blade wipers and flood coolant deep blade teeth free of chips.
Carbide Guide System
Guides are stationary and can be rotated to present new guiding surface to the blade. Upper and lower guides have preloaded carbide-faced back-up blocks to support back edge of the blade.
Blade
14′ 6″ Long x 1″ Wide x .035″ Thick. One Welded-Edge Band Blade is furnished with each machine.
Blade Tension
Blade tension ratchet stops automatically at factory pre-set, 40,000 psi.
Motors
Main; 5 H.P., 1800 RPM, totally enclosed fan cooled. Coolant Pump; 1/8 H.P. enclosed motor-built-in integrally.

18″ x 22″ New Marvel Vertical Tilt Frame Bandsaw Series 8-Mark-II Features:

  • Speed Range: 50 – 450 fpm (15 – 137 m/min) infinitely variable with inverter drive.
  • Front Mounted Speed Control: Allows blade speed to be adjusted from operator’s control station.
  • Feed Pressure: Infinitely variable with control on operator’s panel and Automatic Column Return.
  • Column feed is mechanical with Marvel clutch power feed.
  • T-Slotted Work Table: Work area 24.25″ x 33″ (616 mm x 838 mm); Table height 34.5″ (876 mm)
  • Wheel Diameter: 19″ (482 mm), cast iron wheels.
  • Blade Break/Stall Detection: Standard equipment, shuts off machine in the event of blade breaking or stalling.
  • Quick-Action Vise: Jaws can be shifted to either right or left side of blade.
  • Jaws are 6″ (152 mm) high, 12″ (305 mm) wide.
  • Automatic Stops: Adjustable stops can be pre-set to stop advance and return of blade, and also to stop motor at any
  • location within the 18″ (457 mm) travel of the blade.
  • Flushing Hose: Washes chips from hard to get at places reducing clean-up time.
  • Power Chip Brush: Together with blade wipers and flood coolant deep blade teeth free of chips.

Optional Accessories

  • 575-3-60 VOLT OPTION If ordering the 575 volt machine, it will be wired for 480 volt operation and a transformer will be provided with the machine.
  • 220-1-60 VOLT OPTION A Phase-A-Matic phase converter is shipped with the machine and a 40 AMP service is required.
  • HIGH COLUMN Column 6” longer than standard, providing increased vertical capacity to 28” at vertical position and 17” high at 45°.
  • HIGH JAWS – JAWS ONLY 10” high x 12” wide in place of standard jaws provided with machine. Do not permit miter cutting.
  • 45° HIGH JAWS – JAWS ONLY In place of standard jaws provided with machine. One Front Jaw and one Rear Jaw, both mitered 45°, 10” high x 12” wide.
  • 3° CANTED COLUMN (STANDARD COLUMN) Modification of standard column to add 3° forward approach angle, for increased efficiency in cutting of structural materials. Note: Changes horizontal capacity to 17”.
  • 3° CANTED COLUMN (HIGH COLUMN) Modification of standard High Column to add 3° forward approach angle. Note: Changes horizontal capacity to 16.75”.
  • OPTIONAL HIGH SPEED MODIFICATION 120 – 1080 fpm (36 – 329 m/min); main motor changed to 10 H.P., totally enclosed, fan cooled. Only available in 460-3-60 volt machine order.
  • MIST LUBE – AUTOMATIC Drop Lubrication System. (Requires compressed air connection 60-120psi) SUPPLEMENTARY EQUIPMENT UPON REQUEST.
  • FIRST SECTION DEAD ROLLER CONVEYOR 5’0” LONG, with five ball bearing rollers, 2.5” diameter, spaced on 12” centers, two stands, one end stop, and mounting bracket.  
  • EXTENSION DEAD ROLLER CONVEYOR 5’ 0” LONG, five ball bearing rollers, 2.5” diameter, spaced on 12” centers, one stand, attached to the first section dead roller.
  • FIRST SECTION DEAD ROLLER CONVEYOR FREE STANDING 5’ 0” LONG, with five ball bearing rollers, 2.5” diameter, spaced on 12” centers, two stands, and one end stop.
  • EXTENSION DEAD ROLLER CONVEYOR FREE STANDING 5’ 0” LONG, with five ball bearing rollers, 2.5” diameter, spaced on 12” centers, with one stand.  
  • FIRST SECTION DEAD ROLLER CONVEYOR WITH MANUAL LENGTH GAUGE 10’ 0” LONG, ten ball bearing rollers, 2.5” diameter, spaced on 12” centers, includes Dead Stop, Tilting Type Gauge; manually operated.
  • EXTENSION DEAD ROLLER CONVEYOR WITH GAUGE RAIL 5’ 0” LONG, five ball bearing rollers, 2.5” diameter, spaced on 12” centers. Equipped with gauge rail and measuring tape extensions.  

About Us

Worldwide Machine Tool is the leader in providing full sales, parts and service, financing, transportation and training of new and used machine tools for chip and fabrication clients across the United States, Canada and Mexico. Our warehouse and office is located just minutes north of Columbus, Ohio. With over 25 years of experience in the industrial machine tool industry, we have the knowledge and expertise to provide our customers with the best customer service support and technical expertise on all new and used machine tools to meet their needs.

We buy and sell new and used ironworkers, shears, lathes, milling machines, drills, saws, press brakes, routers, turret punch models, presses, welders, deburring and beveling machines, plate rolls, laser, waterjets and associated tooling and accessories. We take pride in being a trustworthy partner that our customers rely on through the years. Our experienced sales team would love to help you with your next machine tool purchase. Give us a call today or fill out the Request A Quote form on the right side of this page.

Call 614-255-9000 or Contact us today to experience the Worldwide Machine Tool difference.

Terms: Check With Order

F.O.B Factory

Check us out on Twitter, Facebook, Youtube, LinkedIn and Instagram

Reviews

There are no reviews yet.

Only logged in customers who have purchased this product may leave a review.