9″ x 49″ New Sharp Vertical Mill Model LMV-49K-DVS

Price On Request
F.O.B. Factory
Terms: Check with Order

DRO

Required: Enter your voltage requirements.

Description

The Sharp LMV-49K-DVS is a knee type vertical mill with a 9″ x 49″ table and a digital variable speed head. Travels are 36.6″ X, 12″ Y, 16″ on the knee, 5″ on the quill and 12″ on the ram. The 3 HP R8 spindle runs up to 4,500 rpm with runout of 0.0002″ TIR or less, and the quill has three feeds of 0.0015″, 0.003″ and 0.006″ per rev. The head swivels 360° and tilts 45° both ways.

  • Sharp’s patented knuckle head, locked by six bolts in circular T-slots
  • Double bronze nut backlash eliminator with adjusting tool
  • Thrust bearings at the table and saddle screw ends to remove end play
  • Roller bearing support at the bottom of the motor shaft
  • Hard chromed ways, tapered gibs, dual knee and saddle clamps
  • One shot lube with back flow valve; front and rear rubber way covers; tool box

It runs on single or 3 phase power, wired 220 V or 440 V, with low voltage controls. Floor area is 7 x 6.5 x 6.75 ft (W x D x H), and it weighs about 2,100 lbs. Call Worldwide Machine Tool at 614-255-9000 to request a quote.

This Sharp LMV-49K-DVS has a digital variable speed head, so changing spindle speed is quick and simple.

Sharp builds in several details that set it apart from most similar mills. The quill is CNC ground to a mirror finish and chromed to fit its housing, giving nearly jig bore accuracy on quill downfeed. Tapered gibs on the ways make long term adjustment easy. The feed handles spin free, so there is no friction against the operator’s hand. And the underside of the saddle, rather than the top of the knee ways, is hand scraped, which holds oil better and keeps chips and dirt from embedding in the knee ways.

9″ x 49″ New Sharp Vertical Mill Model LMV-49K-DVS Specifications:

Capacity  
Table Size 9″ X 49″
T-slots (No., Size, Pitch) 3, 5/8, 2.5 in.
Table Travel X Longitudinal 36.6″
Table Travel Y Cross 12″
Quill Travel Z Vertical 5″
Knee Travel 16″
Quill Travel 5″
Ram Travel 12″
Spindle Center to Column 6.75 – 18.5″
Spindle Nose to Table Top 2.125 – 18″
Head, Spindle  
Spindle Nose Taper R8
Spindle Variable Speed Range 65-4500 rmp
Spindle Motor (220V/440V) 3 H.P
Quill Feed (Inch/Rev) (3 speeds) .0015, .003, .006 in.
Quill Diameter 3.375 in.
Head Swivel Angle 360°
Head Tilt Angle (L/R) 45°
Head Tilt Angle (Up/Down) 45°
General  
Floor Area (W x D x H) 7 x 6.5 x 6.75 ft.
Approximate Weight  2,100 lbs. 
Power Consumption (220V)  3 KVA/8 amps 
Power Consumption  (440V)  3 KVA/4 amps 

9″ x 49″ New Sharp Vertical Mill Model LMV-49K-DVS Features:

  • DIGITAL VARIABLE SPEED HEAD
    • Easy speed change. Just turn the knob
    • Machine works on Single Phase or 3 phase motor
    • Low voltage control
    • Safety feature includes preventing self-start after power failure of E stop
  • IMPROVED DESIGN OF BACKLASH ELIMINATOR Backlash Eliminator By Double Nut Design replaces the older design that squeezes a split nut to get rid of backlash. Sharp is the first one to use a double nut design that keeps the feed screw in contact with a pair of bronze nuts. Using a custom tool supplied with the mill, the feed nuts are adjusted to control backlash and held tight with a retaining nut and locking ring.
  • PATENTED KNUCKLE HEAD DESIGN New Patented Knuckled-Head Design prevents the head from slipping. The Sharp mills have a knuckle which uses 6 bolts, 3 each side, fitted into circular T-slots with matching nuts securing them from the outside. It locks the head in place for better accuracy and performance than the old design using only 3 bolts to squeeze the casting to hold the head without the T-slots. (Patent No. 5044054)
  • BETTER MOTOR SHAFT SUPPORT  Roller Bearing Support at the bottom of the motor shaft ensures proper loading, support and alignment of the spindle. It also prevents the distortion of the belts due to tension from long years of milling operation
  • CRANK HANDLE IMPROVEMENTS Thrust Bearings mounted at the end of the table and saddle pre-load the feed screw, eliminating end play for precisely controlled lateral movements.
  • 9 x 49 ins table, 12 x 36.6 in. travel
  • Digital Vari speed (DVS), speed change by turning a knob, with digital display of spindle speed
  • R-8 spindle, 3 hp , speed (60-4,500 rpm)
  • Spindle runout of no more than 0.0002 ins TIR
  • Hard chromed ways provide long wear resistance
  • Head tilt side to side, up and down
  • One shot lubrication with back flow valve
  • Tapered gibs for adjustment
  • Dual clamps on knee and saddle that locks the knee and table evenly to the column and saddle to avoid skewing. Handles on the clamp are adjustable to 12 different positions.

9″ x 49″ New Sharp Vertical Mill Model LMV-49K-DVS Standard Accessories

  • One Shot Lube System
  • Hard-Chromed Ways
  • Front and Rear Rubber Way Covers
  • Tool box with tools
  • Wired 220V or 440V.
 

9″ x 49″ New Sharp Vertical Mill Model LMV-49K-DVS Options:

Part # Description Price
440T4 380V, 440V, 575V Transformer – 3 HP $910
AUTOLUBE-2 Auto Lube Pump w/2 Adjustments (installed) $970
SP-250A “Sharp” Power Table Feed with Safety Handle (X-Axis) $925
SP-250B “Sharp” Power Cross Feed with Safety Handle (Y-Axis) $925
SP-250D “Sharp” Power Knee Feed with Safety Handle (Z-Axis) $925
  Factory Installation – Table Feed $335
  Factory Installation – Cross Feed or Knee Feed) $450
5000-2126A 6 “Kurt” Vise with Swivel Base D688 $1,470
ACC-10LMV-NT30 Right Angle Milling Attachment with Arbor for NT#30 Taper $2,270
ACC-10LMV-R8 Right Angle Milling Attachment with Arbor for R-8 Taper $2,270
LMV-D/A Drill & Arbors $560
ACC-26 Riser Block 6″ $1,250
  Factory Installation – Power Draw Bar (Maxi-Torque) $360
C311-LMV Coolant System with Chip Pan at Base (Pump Included) $970
TR-100 “Maxi Torque Rite” Power Draw Bar $1,040
  Factory Installation – Power Draw Bar (Maxi-Torque) $365
ACC-R8 R-8 Collet (Set of 11) 1/8″ – 3/4″ by 1/16″ $280
CK-104 Clamping Kit (52 pcs/steel rack) $270
WL-110V55W-S Halogen Worklight $280
  Fagor DRO  
FG-LMV50 2-Axes X & Y (Fagor 20i) $2,075
FG-LMV50-3A 3-Axes X & Y & Z on Quill (Fagor 20i) $2,795
FG-LMV50-3AK 3-Axes X & Y & Z on Knee(Fagor 20i) $2,920
  Acu-Rite 203S DRO  
AR-LMV50 2-Axes X & Y $3,195
AR-LMV50-3A 3-Axes X & Y & Z $3,590
AR-LMV50-3AK 3-Axes X & Y & Z on Knee $4,521
AR0LMV50-4AK 4-Axes X & Y & Quill & Knee (Z) P.O.R
  Newall NMS – 800 DRO  
NWN-LMV50 2-Axes X & Y $2,170
NWN-LMV50-3A 3-Axes & Y & Z on Quill $2,955
NWN-LMV50-3AK 3-Axes & Y & Z on Knee $2,955
  Factory DRO Installation   
  2-Axes DRO $660 
  3-Axes DRO $995 
  4-Axes DRO  P.O.R 

About Us

Worldwide Machine Tool is the leader in providing full sales, parts and service, financing, transportation and training of new and used machine tools for chip and fabrication clients across the United States, Canada and Mexico. Our warehouses and office is located just minutes north of Columbus, Ohio. With over 28 years of experience in the industrial machine tool industry, we have the knowledge and expertise to provide our customers with the best customer service, support and technical expertise on all new and used machine tools to meet their needs. 

We buy and sell new and used ironworkers, shears, lathes, milling machines, drills, saws, press brakes, routers, turret punch models, presses, welders, deburring and beveling machines, plate rolls, laser, waterjets and associated tooling and accessories. We take pride in being a trustworthy partner that our customers rely on through the years. Our experienced sales team would love to help you with your next machine tool purchase. Give us a call today or Request A Quote. Call 614-255-9000 or Contact us today to experience the Worldwide Machine Tool difference. 

Check us out on Twitter, Facebook, Youtube, and Instagram.

Worldwide Machine Tool LLC.

Terms and Conditions: https://www.worldwidemachinetool.com/terms-conditions/